Cable Termination Gear

Wedge Grip (for EHS Cable)

From the inventors of the Preformed Dead-End Grip comes this heavy-duty remake of a centuries-old technique for buttoning a wire’s end. The Wedge Grip uses tension and a mechanical wedge to grip 7-strand guy wire.

Wire Stop by RIGGUY, 3/8-in to 5/16-in

This unique cable termination simplifies the installation process for 7-strand EHS cable by elimination the need for lags and bolts.

Wire Stop Finishing Cap, 3/8-in & 5/16-in

The Finishing Cap is not a necessary component of the Wire Stop. It does, however, give a finished appearance and protection from exposed wire ends. Made of UV protected vinyl.

Wire Stop by RIGGUY, 1/4-in to 3/16-in

This unique cable termination simplifies the installation process for 7-strand EHS cable by elimination the need for lags and bolts.

Wire Stop Finishing Cap, 1/4-in & 3/16-in

The Finishing Cap is not a necessary component of the Wire Stop. It does, however, give a finished appearance and protection from exposed wire ends. Made of UV protected vinyl.

Wire Stop Hub by RIGGUY for 3/16-in to 3/8-in Wire

The Wire Stop hub is the middle of a "hub and spoke" system for joining three trunks or leaders together. Our hub solution is less invasive than triangulation, requiring only three holes instead of six.

1/4" Dead End Guy Splice, Yellow

Since EHS cable cannot be hand splice, use these dead end cable wraps & the correct thimble to create "spliced" eyes for static cable installation - a dead end guy splice.

3/16" Dead End Guy Splice, Red

Since EHS cable cannot be hand splice, use these dead end cable wraps & the correct thimble to create "spliced" eyes for static cable installation.

3/8" Dead End Guy Splice, Orange

Since EHS cable cannot be hand splice, use these dead end cable wraps & the correct thimble to create "spliced" eyes for static cable installation.

1/4" Heavy Duty Thimble

Thimbles* are used to reduce abrasion of the cable and the lag, and also increases the bend of the cable to insure longer lasting life of your installation.

*ANSI requires that heavy-duty thimbles be used in tree cabling systems.

3/8" Heavy Duty Thimble

Thimbles* are used to reduce abrasion of the cable and the lag, and also increases the bend of the cable to insure longer lasting life of your installation.

*ANSI requires that heavy-duty thimbles be used in tree cabling systems.

5/16" Heavy Duty Thimble

Thimbles* are used to reduce abrasion of the cable and the lag, and also increases the bend of the cable to insure longer lasting life of your installation.

*ANSI requires that heavy-duty thimbles be used in tree cabling systems.

1/2-in National Course Threaded Rod, 6-ft

Brace Rods are used to reduce spreading of two or more leads. Galvanized.

5/8-in National Course Threaded Rod, 6-ft

Brace Rods are used to reduce spreading of two or more leads. Galvanized.

1/2-in Lag Threaded Tree Rod, 6-ft

Brace Rods are used to reduce spreading of two or more leads. Grade 8 Steel.

5/8-in Lag Threaded Tree Rod, 6-ft

Brace Rods are used to reduce spreading of two or more leads. Galvanized.

3/4-in Lag Threaded Tree Rod, 6-ft

Brace Rods are used to reduce spreading of two or more leads. Grade 8 Steel.

1/2-in Hardened Washer

Washer for part number 15027

5/8-in Hardened Washer

Washer for part number 15028

1/2-in 13 Thread National Course Eye Nut

For through bolt cabling. Galvanized.1/2"+Y658 13 Thread

5/8-in 11 Thread National Course Eye Nut

For through bolt cabling. Galvanized.

1/2-in Nut for Rod w/ 13 Thread

Nut for part number 15027

1/2-in Nut for Lag Thread Tree Rod

Nut for part number 19513

5/8-in Nut for Lag Thread Tree Rod

Nut for part number 19517

3/4-in Nut for Lag Thread Tree Rod

Nut for part number 19514

5/8-in Nut for National Course Rod

Nut for part number 15028

Right Hand J-Lag, 1/4"

J-Lag 1/4" x 4" RIGHT (3 1/4") Hand Thread

Right Hand J-Lag, 3/8"

J-Lag 3/8" x 4 1/2" Right (3 1/4") Hand Thread

Right Hand J-Lag, 1/2"

J-Lag 1/2" x 6" Right (4 1/2") Hand Thread

Left Hand J-Lag, 1/2"

J-Lag 1/2" x 6" Left (4 1/2") Hand Thread

Right Hand J-Lag, 5/8"

J-Lag 5/8" x 7" Right (5 1/2") Hand Thread

Left Hand J-Lag, 5/8"

J-Lag 5/8 x 7" Left (5 1/2") Hand Thread

Turn Buckle

1/2 X 8"

Eye Bolt 1/2-in x 8-in w/Nut & 2 Washers

For support of larger diameter trees, where j-lags cannot be used.
Drop Forged & Galvanized Steel. 4-in long threads.

Eye Bolt 1/2-in x 18-in w/Nut & 2 Washers

For support of larger diameter trees, where j-lags cannot be used.
Drop Forged & Galvanized Steel. 9-in long threads.

Eye Bolt 5/8-in x 12-in w/Nut & 2 Washers

For support of larger diameter trees, where j-lags cannot be used.
Drop Forged & Galvanized Steel. 4-in long threads.

Eye Bolt 5/8-in x 18-in w/Nut & 2 Washers

For support of larger diameter trees, where j-lags cannot be used.
Drop Forged & Galvanized Steel. 9-in long threads.

Eye Bolt 5/8-in x 24-in w/Nut & 2 Washers

For support of larger diameter trees, where j-lags cannot be used.
Drop Forged & Galvanized Steel. 12-in long threads.